|
Post by Nightpath on Mar 3, 2015 15:27:48 GMT -4
|
|
ronin
Jeeper
Out on the Mira
Posts: 661
|
Post by ronin on Mar 3, 2015 22:53:59 GMT -4
Yeah , I was waiting for that .
|
|
|
Post by Cherokee Chief on Mar 5, 2015 21:09:10 GMT -4
Got my front d44 all Lincoln locked, trussed, RCV's installed and resealed. Ready to install in the buggy this weekend.
|
|
|
Post by Cherokee Chief on Mar 7, 2015 17:26:01 GMT -4
|
|
|
Post by Cherokee Chief on Mar 9, 2015 20:06:19 GMT -4
Worked on the front diff some more tonight. Brake Line to the Right Side Caliper & Hub all Installed Right Side Brake Line to the Left Side Caliper & Hub all Installed Left Side Brake Line and Power Steering Hoses Fastened to the Upper Link
|
|
rue
Jeeper
Buggy!
DARE YA
Posts: 2,022
|
Post by rue on Mar 9, 2015 20:38:11 GMT -4
Your gettin close.
|
|
|
Post by Cherokee Chief on Mar 9, 2015 20:42:32 GMT -4
Yes Rue I am. I can see a little white dot of light at the end of the tunnel
|
|
|
Post by SocialWheeler on Mar 10, 2015 17:16:07 GMT -4
Why did you choose to weld the front?
|
|
|
Post by Cherokee Chief on Mar 11, 2015 12:42:28 GMT -4
Cheapest route for me at this time, with full hydraulic steering & RCV Axles it shouldn't be an issue steering
|
|
|
Post by Cherokee Chief on Mar 21, 2015 20:04:49 GMT -4
Got some more done. Wont be long now. I think I need a taller high lift Rear end all hooked up Welding up the rear driveshaft Rear tires on Rear drive shaft in Front tires on and steering linkage on Got it outside. This is far as I could get in 2wd. Out in the driveway, NOT liking the lean. I think I need different springs maybe? Interesting shot Rear turned out good Gotta make the side skins, but the diamond plate adds a little bling. Couldn't wait for the snow to melt so I took action. Cost me $60.00 bit it was worth it. Cool image
|
|
|
Post by geezer on Mar 21, 2015 22:32:44 GMT -4
Looks good Darren. Don't worry about the lean too much just yet. Mine did that since new but always seemed to straightened out when I drove it.
|
|
justajeep
Moderator
Valley - VP
Bear River, NS
Posts: 7,214
|
Post by justajeep on Mar 22, 2015 8:45:49 GMT -4
Saw vids on facebook, looks and sounds good!
|
|
|
Post by Cherokee Chief on Mar 22, 2015 10:17:48 GMT -4
Thanks Alan, Open exhaust right off the Y-Pipe. going 3" with a muffler so it will tone it down a bit
|
|
Creepy
Administrator
Dartmouth
Posts: 18,718
|
Post by Creepy on Mar 22, 2015 17:10:53 GMT -4
Saw vids on facebook, looks and sounds good! Same, looks good! X2 on the lean, drive it a bit, don't worry. My airshocks will do that after sitting too.
|
|
|
Post by Cherokee Chief on Apr 3, 2015 16:36:05 GMT -4
Well took the buggy down to work so I can get it on the hoist to center and square the diffs to the chassis. Did the rear first then centred and squared the front to the rear. set the toe and now my suspension is done and complete. I also got my boss to bring in his race car scales. and here are the results 3400lbs Heavier than I was expecting but still ok
|
|