dan
Jeeper
Membership Co-ord - Valley
Posts: 3,397
|
Post by dan on Apr 28, 2013 8:09:49 GMT -4
Bill, how's your rear d-shaft going to look? I can't tell in the pictures, did you push the engine up close to the rad?
|
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on Apr 28, 2013 9:38:24 GMT -4
Drive shafts are in the same spot.The t case was attached to trans and layed in the skid plate where it was with the 4.0
|
|
dan
Jeeper
Membership Co-ord - Valley
Posts: 3,397
|
Post by dan on Apr 28, 2013 12:04:16 GMT -4
Cool
|
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on Apr 28, 2013 19:49:28 GMT -4
Went in today and got the top and doors on also installed hood.Its not running yet but still have to add everything else Attachments:
|
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on Apr 30, 2013 21:11:19 GMT -4
Well next step is wiring were hoping it will be running this weekend. Attachments:
|
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on Apr 30, 2013 21:13:24 GMT -4
And im gonna build some flat tube fenders and im thinking these will work for marker lights Attachments:
|
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on May 6, 2013 20:50:48 GMT -4
Well we got the wiring all out of the 2 harnesses we didn't need and soon to start tieing them in together.Also done both driveshafts installed dash installed.To do POR15 the Tub rebuild the rear locker,front axle seals new control arm bushings. Need to wait on the rad I had to order from mishimoto. Attachments:
|
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on May 15, 2013 21:52:44 GMT -4
Well had it running tonite but runs for a couple seconds then shuts off.So at least I know we got the main wires connected that are needed. But still a big list of to dos yet
|
|
dan
Jeeper
Membership Co-ord - Valley
Posts: 3,397
|
Post by dan on May 16, 2013 4:07:31 GMT -4
would that be the security system that is shutting the engine down Bill? or or something else?
|
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on May 16, 2013 5:47:32 GMT -4
dont think it is the security cause theres no pin outs at the pcm for security.
|
|
Big G
Hardcore
Posts: 5,146
|
Post by Big G on May 16, 2013 7:52:01 GMT -4
That happened to me when I started my buddy's cummins with my TJ key. Run a couple seconds then die. Took me a couple starts to figgure it out.
|
|
The Garagemahal
Moderator
Build Thread King
Resident Army Ranger , Navy Seal , Super-Warrior , Ninja !!
Posts: 11,518
|
Post by The Garagemahal on May 16, 2013 16:12:34 GMT -4
dont think it is the security cause theres no pin outs at the pcm for security. Your jeep have a grey Key ? how about the donor rig ?
|
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on May 16, 2013 16:31:03 GMT -4
neither jeeps have chip in them
|
|
The Garagemahal
Moderator
Build Thread King
Resident Army Ranger , Navy Seal , Super-Warrior , Ninja !!
Posts: 11,518
|
Post by The Garagemahal on May 16, 2013 17:25:35 GMT -4
Check the ASD relay ?
|
|
Stevens
Jeeper
2008 Mud Pit Master
Posts: 3,240
|
Post by Stevens on May 16, 2013 18:01:46 GMT -4
Sounds exactly like what happens when the security system isn't deactivated by the door lock sensors.
|
|