tchase
Jeeper
Steering Committee - Valley
Posts: 489
|
Post by tchase on Jun 8, 2009 13:57:09 GMT -4
What's Left??!!! Let's see... Take pile of scrap metal in garage, add pile of scrap metal on front lawn, plus a bit more from the back yard, combine peices into something that resembles a Jeep.  Wish I had High speed so I'd have time to post up a few pics of what it looks like right now, pretty scary for only having 3 days left. I've been at it all day though and it is coming together pretty well. Should be test fitting the new box sometime this evening if anyones in the area and wants to stop by and help lift it on there. |
|
4X4PLAY
Elite
~ P.O.R.N. FOR SALE ~
Posts: 11,763
|
Post by 4X4PLAY on Jun 8, 2009 14:03:25 GMT -4
Let's just hope my parts show up today  Jeff Not looking good, wrong parts arrived today...got a Napa part # now, but soonest is a few days  I'm still searching! Jeff |
|
mrg
Jeeper
Steering Committee - Halifax
Posts: 2,705
|
Post by mrg on Jun 8, 2009 14:06:34 GMT -4
My brake caliper is at the dealer but I will assume its the wrong one until I see it. lol I'll go anyway even with a stick-ish caliper.
|
|
littlemulticoloredwagoneer
Moderator 
Trail Master/Jam Co-chair - Valley
Buy it, Build it, Break it!!...........REPETE!
Posts: 2,310
|
Post by littlemulticoloredwagoneer on Jun 8, 2009 16:05:05 GMT -4
Cracked head.. being replaced... still more... anyone have rewind button??
|
|
tchase
Jeeper
Steering Committee - Valley
Posts: 489
|
Post by tchase on Jun 8, 2009 16:27:57 GMT -4
Steel for the box crossmembers didn't come in this morning like it was supposed to  Guess the test fitting will have to wait till tomorrow night, followed immediately by the final fitting. |
|
mlc
Jeeper
Zuk'er
Posts: 334
|
Post by mlc on Jun 8, 2009 16:51:44 GMT -4
my rig is ready ;D
|
|
newbiejeeper
Jeeper
YOU, a published writer?..Internet don?t count. Any asshole can throw shit up on there
Posts: 2,494
|
Post by newbiejeeper on Jun 8, 2009 18:29:42 GMT -4
Like she would let you go even if she had the baby in the next 2 days. ;D I know I know Dont worry I will stick back here and make sure the Jeep board is ok... |
|
BILL
Jeeper
Posts: 3,029
|
Post by BILL on Jun 8, 2009 19:47:13 GMT -4
got to change all fluids tommorow front rear diffs tranny and t case...got a look at the rear diff fluid tonite when i did the yoke and seal and its like mollasses in the winter
|
|
|
|
Post by jeepfever on Jun 8, 2009 20:15:55 GMT -4
I'm about to head outside to weld a couple of patches of sheet metal to the tub/fenders. If there's daylight left maybe I'll even change the engine oil. The bodywork is done and the fender flares are back on. I'll go over my checklist and see what's next. Maybe an oil change and check the diff & transfer case fluid levels. |
|
|
|
Post by tothewall on Jun 8, 2009 21:33:25 GMT -4
I am ready to rock and or roll. See you all there. ETA 1500 on Thursday. Leaving Yarmouth around 1300ish
|
|
mrg
Jeeper
Steering Committee - Halifax
Posts: 2,705
|
Post by mrg on Jun 8, 2009 21:49:32 GMT -4
Woo hoo RR caliper is done, new rear flex line installed, rear brakes bled, adjusted exhaust to not hit rear track bar and front track bar installed.
All thats left is to adjust front control arms so front track bar does not hit diff cover and install front flex lines and bleed front brakes.
|
|
|
|
Post by blacksheepxj on Jun 8, 2009 21:53:50 GMT -4
Get an oil change and I am done.
Rob
|
|
The Garagemahal
Moderator
Build Thread King
Resident Army Ranger , Navy Seal , Super-Warrior , Ninja !!
Posts: 11,518
|
Post by The Garagemahal on Jun 9, 2009 0:18:54 GMT -4
D 30 R&P install |
|
|
|
Post by peterandkaren on Jun 9, 2009 22:39:20 GMT -4
Install CB
Remove back seat
Chase power steering leak
Pack every crevice of the jeep
Can't wait to go!
|
|
The Garagemahal
Moderator
Build Thread King
Resident Army Ranger , Navy Seal , Super-Warrior , Ninja !!
Posts: 11,518
|
Post by The Garagemahal on Jun 9, 2009 23:33:08 GMT -4
Pack like I have never packed before ;D
|
|
I'm still searching! 
Guess the test fitting will have to wait till tomorrow night, followed immediately by the final fitting.
