|
Post by DamnJeep on Oct 3, 2011 20:47:50 GMT -4
Since I decided to get rid of the doubler I had to make two new driveshafts and re-route the exhaust. Rear shaft was no problems however I ran into some issues with the front. Uploaded with ImageShack.usUploaded with ImageShack.usUploaded with ImageShack.usThe u-joint at the t-case sides is sooo close that if the suspension cycles it would bind the joint. As you can tell from the last picture the type of yoke I'm using (similar to the one on the right) is too shallow so there is no room for the joint to move and not enough material to grind off. So I need a deeper yoke like the others. Anyone have one they want to part with? To fit a 2" tube.
|
|
|
Post by 540rock on Oct 3, 2011 22:45:15 GMT -4
yokes are normally really cheap at parts for trucks or drive products. mine were only 18$ each.
|
|
chevystroker
Jeeper
NEVER CONFUSE HAVING A CAREER WITH HAVING A LIFE ! ! ! ! ! !
Posts: 896
|
Post by chevystroker on Oct 4, 2011 4:40:12 GMT -4
Looks like the bolts for the strap would hit first. Perhaps a U-bolt style yoke would help. You might be able to convert that to a U-bolt style by drilling it out, IF there is a large enough flat area on the back side for a nut to fit.
|
|
90bronco
Jeeper
just smitin'
Posts: 3,415
|
Post by 90bronco on Oct 4, 2011 18:11:11 GMT -4
Couple of my buddies did their rear d-shafts with ford u-bolt straps from a front d-shaft that i gave them , worked well but yours might still be too tight .
|
|
justajeep
Moderator
Valley - VP
Bear River, NS
Posts: 7,214
|
Post by justajeep on Oct 4, 2011 19:16:38 GMT -4
I'll try to remember to look through my driveshaft parts, I probably have a deeper yoke. I should have u-bolt yoke for a 300 too.
|
|
rue
Jeeper
Buggy!
DARE YA
Posts: 2,022
|
Post by rue on Oct 4, 2011 20:10:00 GMT -4
Yokes off of a dana 44 will fit the 300. As for the drive shaft yoke,I modified a slip yoke to fit in the tube instead of a weld yoke.
|
|
|
Post by DamnJeep on Oct 4, 2011 20:38:08 GMT -4
Yokes off of a dana 44 will fit the 300. As for the drive shaft yoke,I modified a slip yoke to fit in the tube instead of a weld yoke. Damn you beat me to it! I was just in the shop looking at the slip yoke and was wondering if I turned it to fit the 2" .25 wall DOM I have would it work... Didn't think about the 44 yoke. I may even have one around here somewhere but will try the slip first. Thanks to Steve (beaver on the board) for the driveshaft.
|
|
|
Post by Zach "Hulltech Redneck" on Oct 8, 2011 12:29:21 GMT -4
i got a question about drive shafts, i got into this sort of problem with my back shaft, can you put a double cardon joint on the back shaft?
|
|
The Garagemahal
Moderator
Build Thread King
Resident Army Ranger , Navy Seal , Super-Warrior , Ninja !!
Posts: 11,518
|
Post by The Garagemahal on Oct 8, 2011 17:09:10 GMT -4
i got a question about drive shafts, i got into this sort of problem with my back shaft, can you put a double cardon joint on the back shaft? What jeep / t case do you have ?
|
|
dan
Jeeper
Membership Co-ord - Valley
Posts: 3,397
|
Post by dan on Oct 8, 2011 18:47:49 GMT -4
for most TJ's or YJ's with more than a couple inches of lift, it is recommended to have a rear driceshaft with a double cardan joint on the t-case end.
|
|
|
Post by Zach "Hulltech Redneck" on Oct 9, 2011 22:20:32 GMT -4
i have a moded yj, i have wagoneer 44 diffs and a i forget the t-case, it was bolted up to a 700r4e ... i have a 350 sbc in er, im thinking thats what im going to have to do.... the double cardon joint
|
|
|
Post by DamnJeep on Oct 10, 2011 8:27:35 GMT -4
i have a moded yj, i have wagoneer 44 diffs and a i forget the t-case, it was bolted up to a 700r4e ... i have a 350 sbc in er, im thinking thats what im going to have to do.... the double cardon joint You have to know if the case has a fixed yoke, flange or is a slip joint out put. As was mentioned typically on a short wheel base like a YJ it is a good idea to run a double cardan shaft as the driveline angles are too great for the normal driveshaft. A double cardan shaft is basically 3 u-joints instead of 2. Where the upper two joints act to reduce the operating angle of the joints by half for each joint involved. Then you shim or somehow rotate the pinion up to more or less point at the trans output thereby reducing its operating angle as well. That was a pretty quick explanation and there is a lot more detail than that involved but just get the double cardan shaft and be happy! See pics attached. Uploaded with ImageShack.usUploaded with ImageShack.us
|
|
|
Post by Zach "Hulltech Redneck" on Oct 10, 2011 15:38:39 GMT -4
ok yeah, i understand that, i have a slip out flange in the t-case... does that mean i cant use a double cardon joint?
|
|
|
Post by redkj666 on Oct 10, 2011 16:44:07 GMT -4
ok yeah, i understand that, i have a slip out flange in the t-case... does that mean i cant use a double cardon joint? If you have a Slip Yoke You can either get a full on Slip yoke eliminator kit, or a Hack N' Tap kit so you can run a double cardan setup.
|
|
|
Post by Zach "Hulltech Redneck" on Oct 10, 2011 17:40:09 GMT -4
ooo a hack n tap job ... i got ya. thanks
|
|