90bronco
Jeeper
just smitin'
Posts: 3,415
|
Post by 90bronco on Jan 22, 2011 10:34:10 GMT -4
Oh, sorry I meant to get right back to you on that. They don't offer that specific application but I can order custom lengths and splines, Im guessing you want all 3 shafts? Not sure how much clearance you would have on the inboard joint but you need almost 4" Cool , i don't think there's 4"in there but i'd have to measure it . Just looking for options as i also may have a d50 front and 10.5 rear coming soon. Do you need total axle length and spline count of both ends to get a price?
|
|
iwonajeep
Jeeper
Jeepin is tasty says Buddy
Posts: 961
|
Post by iwonajeep on Jan 22, 2011 15:17:45 GMT -4
I'll fire you a quote next week, I don't need measurement for that. I would only need inner axle length measuring from the centre of the u-joint and spline count, the outers are all the same for ford. Is there anything differrent about the end of that shaft where it joins the other shaft?
|
|
Creepy
Administrator
Dartmouth
Posts: 18,718
|
Post by Creepy on Jan 22, 2011 16:23:55 GMT -4
That was easy, took all but 5 minutes. I'm going to use the cats lazer vision to weld it together. Wicked! How much for the cat? Alan - the tapered reamer - do you power feed that, or use the machine to keep it square and hand turn it?
|
|
rue
Jeeper
Buggy!
DARE YA
Posts: 2,022
|
Post by rue on Jan 22, 2011 17:31:33 GMT -4
That was easy, took all but 5 minutes. I'm going to use the cats lazer vision to weld it together. Very nice,Going to be interesting to see how the 44 holds up with the RCV shafts.Wonder who's going to be the first to pop a R&P..LOL What did you use for the tubes?
|
|
iwonajeep
Jeeper
Jeepin is tasty says Buddy
Posts: 961
|
Post by iwonajeep on Jan 22, 2011 17:47:21 GMT -4
3 x 1/2" mechanical tubing, I'm thinking an axle shaft before a RG but well see, may even blow the engine trying to break stuff
|
|
justajeep
Moderator
Valley - VP
Bear River, NS
Posts: 7,214
|
Post by justajeep on Jan 22, 2011 17:52:19 GMT -4
The reamer is hand fed, but machine power turns it.
|
|
90bronco
Jeeper
just smitin'
Posts: 3,415
|
Post by 90bronco on Jan 22, 2011 18:11:04 GMT -4
I'll fire you a quote next week, I don't need measurement for that. I would only need inner axle length measuring from the centre of the u-joint and spline count, the outers are all the same for ford. Is there anything differrent about the end of that shaft where it joins the other shaft? i'll get you a measurement of both side inner's nothing different i don't think .
|
|
Creepy
Administrator
Dartmouth
Posts: 18,718
|
Post by Creepy on Jan 22, 2011 18:12:42 GMT -4
The reamer is hand fed, but machine power turns it. Do you recall the rpm?
|
|
The Garagemahal
Moderator
Build Thread King
Resident Army Ranger , Navy Seal , Super-Warrior , Ninja !!
Posts: 11,518
|
Post by The Garagemahal on Jan 22, 2011 18:30:12 GMT -4
Beefy ! Should hold up great ! Whats the plan for the steering linkage ?
|
|
iwonajeep
Jeeper
Jeepin is tasty says Buddy
Posts: 961
|
Post by iwonajeep on Jan 22, 2011 19:36:52 GMT -4
Well you talked me out of cross over Scott, so I'm using the knuckles for the tierod and on top of the passengers side knuckle is the steering arm, I'm using ton joints for the complete just-a-flex steering setup
|
|
|
Post by backwoodsLJ on Jan 23, 2011 8:27:01 GMT -4
I look at this thread every time I'm on here,very cool build for sure! I'm just noticing the cat in the backround now,is he the pecks mascot? Now I get the lazer vision joke! ;D
|
|
90bronco
Jeeper
just smitin'
Posts: 3,415
|
Post by 90bronco on Jan 23, 2011 8:31:28 GMT -4
I look at this thread every time I'm on here,very cool build for sure! I'm just noticing the cat in the backround now,is he the pecks mascot? Now I get the lazer vision joke! ;D lol me too every time i come on , gave me a couple ideas .
|
|
mlc
Jeeper
Zuk'er
Posts: 334
|
Post by mlc on Jan 23, 2011 16:32:05 GMT -4
3 x 1/2" mechanical tubing, I'm thinking an axle shaft before a RG but well see, may even blow the engine trying to break stuff give it to jeff... he will break the r/p fer ya ..lol... looks awesome ...alot of work going into it
|
|
Big G
Hardcore
Posts: 5,146
|
Post by Big G on Jan 23, 2011 17:53:57 GMT -4
3 x 1/2" mechanical tubing I'd be interested in a cost & weight comparison to a 60. ;D Poke poke.
|
|
dan
Jeeper
Membership Co-ord - Valley
Posts: 3,397
|
Post by dan on Jan 23, 2011 19:38:48 GMT -4
but what are replacement parts worth on a 60 compared to on a 44 also?
|
|